Usually the Linksys Velop system setup is done with one goal which is having fast and reliable internet within the entire house. But sometimes, despite doing everything right during the Linksys Velop setup, your WiFi is unable to connect. That red light shows up and suddenly you observe that there is no internet. It is frustrating. This thing happen many times and there is no need of technician. With the help of this guide you will understand what is causing the issue and how you can fix it. 
Let’s get started.

1. Look for The basics First
Before any further discussion, start simple.
⦁    Ensure that your modem is working. 
⦁    Check the ethernet cable that connects your modem to the main Velop node.
⦁    Restart the modem and the Velop system.
Sometimes it is possible that there is no problem with your Velop but with the internet provider. Also, double-check your Linksys Velop setup steps to ensure you did not miss anything during the initial installation. If you forgot even the single thing it will cause a trouble. 

2. Reboot the Velop System
With the help of simple reboot lot of issues can be solved. 
⦁    Unplug the Velop nodes.
⦁    Wait for 10-15 seconds atlesat.
⦁    Plug them back in and starting with the primary node.
Let them boot up completely before testing the connection. A simple power cycle can reset minor bugs that stop your internet from working.
Tip: Do this whenever your Velop acts weird. It is similar to give it a fresh start. 

3. Check for Firmware Updates
Outdated firmware can block internet access.
⦁    Open the Linksys Velop login page from the browser and type in the address bar 192.168.1.1 or you can use the Linksys app.
⦁    Enter your admin credentials.
⦁    Check for the firmware updates. 
⦁    If there is a new version available then update it.
Outdated software can result into connection drops, delays or total loss of internet. Keeping your firmware updated is a simple way to avoid internet issues. 
Also, make sure that your login credentials for the Linksys Velop login page are correct. Sometimes login errors also lead to network configuration issues too.

4. Factory Reset as a Last Resort
If nothing works then do a full reset.
Here is how to do it:
⦁    Press and hold the reset button on the main node for about 10 seconds until the light starts blinking red.
⦁    Wait until it restarts completely. 
⦁    Now, repeat the Linksys Velop setup process again.
The factory reset removes all the settings or errors and offer you a clean slate to work with. Be ready to set up your WiFi name and password again, as it wipes everything. 
And remember once after a reset always complete the Linksys Velop login process carefully to avoid old mistakes.

5. Positioning of the Nodes Matters
Yep, placement can affect connectivity too.
If your Velop node is too far from the modem or surrounded by walls then the signal might drop which causes an internet issue.  
Tips:
⦁    Keep your primary node near the modem with a short Ethernet cable.
⦁    Keep nodes out in the open area and not in cabinets or behind TVs.
⦁    Space the secondary nodes so they are not too far from the main one.
Wrong node placement can break the mesh connection, especially if you rushed through the Linksys Velop setup without checking signal strength.

7. Check Parental Controls or Device Blocking
If only some devices are not connected and others are connected then it is because of some settings inside your Linksys system.
⦁    Log in using the Linksys Velop login page.
⦁    Go to device settings.
⦁    See if any devices are paused or blocked.

8. Use the Linksys App for Troubleshooting
The Linksys app makes troubleshooting easier.
⦁    It shows real-time internet status.
⦁    It alerts you if one of the nodes is down or if the modem is not detected.
⦁    You can even reset or update the network from your phone.
Using the app during the Linksys Velop setup process also helps avoid configuration issues. It is not just for setup but it is your digital toolbox.

9. Double-Check the Login and Admin Settings
Sometimes, people forgot what they entered during the time of setup. 
If you entered the wrong ISP settings during the Linksys Velop setup then your system might fail to connect.
Solution:
⦁    Go to Linksys Velop login page.
⦁    Reset to default DNS or auto settings.
⦁    Reboot and check if the internet returns.
There is no need to always reset the entire system and with this also the issue can be solved. 

Final Thoughts
Even the WiFi systems like Linksys Velop can also face some minor problems. Make sure to follow the steps slowly to avoid any mistake and check your settings with the help of Linksys velop login. With a few careful fixes, your internet will be back and working just fine.